Showing results: 1171 - 1185 of 2454 items found.
-
B-1020-C -
ROSS ENGINEERING CORPORATION
These supply 120V or 240V AC continuous power for equipment that must operate while at a high voltage to ground or power source. For example, a fiber optic transmitter at the HV level for waveforms to be received and measured or recorded by grounded instrumentation might be powered by an isolation transformer secondary to primary either insulated by potting, oil or air. The low dielectric constant of air insulation provides lower capacitive coupling between the secondary and the primary or ground than would solid or oil insulation. The lower capacitance provides better isolation both at line frequency and especially at high frequency voltages such as lightning or switching transients.
-
B-1020-B -
ROSS ENGINEERING CORPORATION
Ross Engineering Corporation has developed a HV compact analog fiber optic transmitting and receiving system, with optional over-voltage limiting, designed to drive instrumentation from a DC to 1MHz signal source. The system is available with optional multiple input and output ranges of ±0-1V PK, 0-5V PK to 0-10V PK. It will also operate in conjunction with Ross Engineering Corporation’s high accuracy high voltage wideband voltage dividers, which are useful from DC to over 10MHz up to 1,000,000V PK at 0.01% to 3% accuracy. Transmitters and receivers can be powered by either AC or DC.
-
AJIT Electronics Co.
This is a common test panel for distribution/ power transformers of different specifications. The user can perform most of the factory tests, as per the relevant IS standard for the transformers. The panel consists of power analyser, meters for high voltage test, meters for induced voltage test etc, control for all the tests, protection and interlock circuits so that a single panel can be used to conduct a number of tests using only one dimmerstat and the associated devices
-
TD3202M -
Aplab Limited
- Fully Metallic Construction to Stop Radiated EMI- Compact & Rugged Design- DC Output ON/OFF on each Main Output- Voltage & Current Output Preset Facility for Safety- Constant Voltage / Constant Current Mode- 3 Digit DPM V and A- High Stability & Close Regulation ±0.01% +3mV- Low Ripple <1mV rms- Overload Protection- Convection Cooled – No Fans- Meets International Safety Standards
-
Spark P3 -
Manta Test Systems
Doble Spark P3 is a universal partial discharge (PD) and electromagnetic interference (EMI) analyzer that uses a software defined radio signal detector to identify characteristics of insulation system deterioration that could lead to the failure of high voltage equipment. It detects signals from suitable sensors in a frequency range between 9 kHz to 2 GHz for PD and EMI, and DC to 500k Hz for acoustic and reference voltage measurements.
-
Precision Analog Systems Co.
Precision Analog Systems signal conditioning output amplifiers can increase the voltage output drive to +/- 200 Volts at 12 mAmps. Our high current amplifier cards provide 24 Volt output signals with 500 mAmps of output current. PAS offers boards that provide various combinations of output voltage and output current drive capability. Please see below for our current product list.
-
98x -
Vitrek Corporation
The new 981i and 983i Teraohmmeters are designed to tackle the toughest High Resistance measurement applications. Demanding applications that most other IR testers won’t measure up to. So when it’s time to test higher voltage IR values like today’s electric vehicle systems and higher voltage solar arrays — look to Vitrek to deliver the IR tester you need for your production line.
-
Hilo Test
Hilo-Test offers a large number of coupling / decoupling networks for single-phase and 3-phase power supply lines and signal data lines and telecommunication lines. In addition to numerous standard versions Hilo-Test also supplies special variants for higher voltages (e.g. 3x690 VAC or up to 1 KV DC) and high currents (up to 200 A or more), as well as for surge voltages up to 12.kV. TheIEC 61000-4-4/5standardsformainlyvalid.
-
P50 -
Beijing GFUVE Electronics Co.,Ltd.
mv AC clamp on current probe has 1mV voltage or 1mA current output, can measure cable and bus bar, max current is 1000A, high precision, can be used to monitor power quality. Perfect material permalloy core.
-
PW-4033 -
PINTEK Electronics
*4 digits, 4 display*Tracking operation*Low Ripple & Noise: ≦0.4mVrms*High Resolation Read out: 10mv/1mA*10 Turn VR for Voltage and current Setting*Triple output: 0-30V/0-3AX2 ,5V Fixed/0-3A
-
In-Plant Holiday Detector -
Tinker & Rasor
High Voltage Holiday DetectionPulse DC OutputLow Settings: 800v to 8,000vHigh Settings: 3,500v to 35,000v110v / 220v AC Power SupplyIntegrated Digital Volt MeterVisual (LED) Holiday IndicatorAudible Holiday IndicatorRemote Indicator Connection, Audible and Visual
-
MCH Instruments Co.,Ltd.
Features:-Handiness, beautiful, stabilization, high performance, low cost-High Stability digital display DC power supply-A full functional output protection function-Can be continuos output full load-Current/ voltage adjustable within the nominal value
-
HBM, Inc
HBM provides the entire measurement chain for electrical power testing - from electrical machine testing to high voltage and complex inverter control testing in the automotive, ground vehicle, and aerospace industry as well as the manufacturing, production, and energy industries.
-
M9185A -
Keysight Technologies
The M9185A is a fully independent, isolated D/A converter that is capable of supplying high voltage levels in parallel of up to eight or sixteen channels. Each channel is able to output up to 16V as stimulus signals to Device Under Tests (DUTs).
-
Texas Instruments
TI offers the industry's most comprehensive high speed amplifier portfolio with the widest bandwidth and best in class distortion, precision and power consumption across a broad range of supply voltages. Our industry leading FDA's, DVGA's, TIA's and General purpose amplifiers coupled with the reliability and longevity of our parts makes TI the ideal supplier of high speed amplifiers.